Posted in

How to reduce shrinkage in brass castings?

Hey there, fellow brass casting folks! If you’ve ever dealt with shrinkage in your cast parts, you know how frustrating it can be—one tiny void or hole in a brass component can turn a perfect, custom order into a scrap pile, blow your budget, and delay that shipment you’ve been waiting on. As a brass casting supplier with years in the game, I’ve seen it all: a customer’s precision valve casting ruined by mid-size shrinkage, a decor piece that failed a pressure test because of hidden shrinkage, even a batch of 1,000 small bushings that got rejected because of surface voids. Shrinkage doesn’t just hurt our bottom line (or yours, when we have to rework or remake parts) — it wastes time, materials, and headaches for everyone involved. That’s why today, I’m breaking down the practical, science-backed steps we use at our shop to cut shrinkage way down, so you can stop dealing with the same old problems too. Let’s dive in, no stuffy jargon, just real stuff that works. Brass Casting

First, let’s keep this simple: shrinkage in brass castings happens for two main reasons, right? Most people know metal shrinks as it cools, but what they don’t always get is that brass has two phases of shrinkage: liquid shrinkage (when the metal’s still fully melted, before it starts to solidify) and solid shrinkage (when it’s cooling from solid to room temp). Wait, actually, there’s a third phase — the mushy zone, where metal’s partially liquid and partially solid. That’s where 90% of the bad shrinkage comes from, by the way. If you’ve ever seen a deep, dark hole inside a casting, that’s almost always a shrinkage cavity from the mushy zone. If it’s a tiny, pockmark on the surface, that might be surface shrinkage or even gas porosity, but let’s focus on the fixable stuff here.

Let’s start with the biggest culprit for most of us: metal temperature control. You can’t just heat brass to “pretty hot” and call it a day. Too cold, and the metal solidifies too fast before it can fill every nook and cranny — that causes hot spots where shrinkage forms. Too hot, and you get way too much liquid shrinkage, which leads to big, deep cavities that are way harder to fix. For our shop, we’ve found the sweet spot is around 1,850°F to 1,900°F (that’s ~1,010°C to 1,040°C for the metric folks). Wait, but it’s not just the pour temp — it’s also the mold temp. If your sand mold is cold, it will suck heat out of the metal too fast, leading to uneven solidification. We preheat our green sand molds to about 200°F (93°C) for smaller parts, and up to 400°F (204°C) for larger, thicker parts. That slow, even heat withdrawal means the metal solidifies more uniformly, so shrinkage doesn’t get trapped in the middle. Pro tip: We use a simple thermocouple (cheap, super reliable) to check pour temps right before we pour — no more guessing! I’ve seen so many shops wing this, and it’s the number one reason for avoidable shrinkage.

Next up: gating and riser design. This is where a lot of new casters mess up. Gating is the system that brings molten metal into the mold, and risers are the little “metal reservoirs” we add to the top of thick sections of the casting. The whole point of a riser is to supply extra molten metal to the part as it shrinks — think of it like a straw you stick into a cake pan to add more batter as it sets. If your riser is too small, it dries up before the part is done shrinking, and you get a big hole. If it’s too big, you’re wasting metal and time machining it later. For brass, we calculate riser size based on the modulus of the thick section of the part — modulus is just volume divided by surface area, right? So a thick bushing might have a modulus of 1.2, so our riser needs to be at least 1.5 times that modulus to feed the part. Also, we make sure risers are located directly above the thickest spots of the casting — never under, because gravity works against you here. And one more thing: for brass, we use “hot risers” (risers that stay hotter longer) instead of cold ones. We wrap risers in insulating ceramic or even just a thick layer of refractory sand so they cool slower. That way, they’re the last thing to solidify, so they can keep feeding the part. I once had a customer who stopped adding hot risers and cut down on material costs — they got 12% more shrinkage rejects in their next batch. Don’t skip this step, it’s non-negotiable.

Wait, what about mold material? A lot of people use green sand, but if you’re dealing with complex parts or tight tolerances, silica sand might not be the best. Silica sand has a high coefficient of thermal expansion, which means it can put pressure on the brass as it cools — that pressure can actually make shrinkage worse, because it stops the metal from filling in voids. We switched to zircon sand for our precision parts a few years back, and it cut surface shrinkage by like 25% instantly. Zircon is denser, has lower thermal expansion, and gives a smoother surface, which means the metal solidifies more evenly. For larger parts, we use olivine sand — it’s cheaper than zircon, has similar low expansion, and works great for thicker sections. Also, make sure your mold has proper venting! If air gets trapped in the mold, it can create pressure that pushes against the molten metal, preventing it from reaching tiny corners and leading to shrinkage. We add small vent holes (1/8 inch to 1/4 inch) along the gating system and in the top of risers — no more trapped air, no more “dry” shrinkage from poor metal flow.

Then there’s metal alloy composition. Brass is an alloy of copper and zinc, right? But the mix matters a lot for shrinkage. Most common brasses (like C36000, the free-machining one) have about 60% copper, 35% zinc, and 5% lead, but that small zinc content can affect solidification. Wait, alpha-beta brasses (like C85700, which is a common casting brass) have a wider mushy zone, which is where shrinkage happens more easily. If you’re dealing with a high-shrinkage alloy, you can add small amounts of “feeders” or even change the alloy slightly. We’ve found that adding 1-2% tin to some brass mixes tightens the mushy zone, which reduces shrinkage cavities. Just make sure you check your alloy specs — too much tin can make brass brittle, so don’t overdo it. Also, watch out for impurities in your metal! Things like iron or aluminum in the brass can create uneven solidification, leading to shrinkage. We do a simple metal analysis every 50 pours to make sure our brass is clean — no more random shrinkage from junk in the melt.

Wait, let’s talk about solidification rate and section thickness. Shrinkage is way worse in thick sections, obviously. If you have a part with a 1-inch thick wall next to a 1/8-inch wall, the thick wall will cool slower, so shrinkage will form there. That’s called “section thickness variation” — it’s the single biggest design-related cause of shrinkage. Our team works with customers on custom brass castings to adjust the part design: we round sharp corners (sharp corners are hot spots, they cool slower), add fillets, and even thin down thick sections slightly where possible. For example, a customer had a custom valve body with a 1.5-inch thick flange — we suggested adding a small rib to distribute the thickness evenly, and that cut shrinkage in the flange by 30%. Also, if you can, orient your part so the thickest section is on top, directly under a riser — that makes feeding way easier. We’ve had customers come to us with a part designed so the thick section is at the bottom, and we have to spend extra time moving risers to fix it. Pro tip: if you’re designing a new part, shoot for uniform wall thickness as much as possible. It saves you time and money in casting, no question.

Another thing a lot of shops sleep on: post-cast processing? Wait, no — wait, shrinkage can also happen after solidification, during solid shrinkage. When brass cools from solid to room temp, it shrinks another 2-3% in volume. That’s not usually a big issue for small parts, but for large castings (like a 50-pound gear housing), that solid shrinkage can cause warping or tiny surface cracks. To fix that, we use a “settling time” — after pouring, we let the part and mold cool slowly in a controlled environment, instead of dumping it into a water quench. Quenching is great for hardening, but it causes rapid, uneven cooling that makes solid shrinkage worse. For our larger parts, we use a cooling oven set at 200°F to let the part cool gradually over 24 hours. That slow cooling eliminates almost all of the solid shrinkage issues. We also avoid rapid machining right after casting — let the part “stress relieve” for a week before you machine it, especially for tight-tolerance parts. I’ve seen a customer machine a part within 24 hours of casting, and it warped 0.020 inches because of solid shrinkage. Total waste.

Wait, let’s test these steps with real examples from our shop. Last quarter, a customer ordered 5,000 custom brass bushings for a farm equipment engine. Their previous supplier had a 18% shrinkage reject rate, which was costing them like $1,200 per batch in rework. We adjusted the pour temp to 1,870°F, used zircon sand molds, added a small hot riser to each bushing’s end, and fixed the mold vents. Their reject rate dropped to 2% — that’s a huge win for them, and for us too (less scrap, more consistent parts). Another example: a client needed a large brass valve body for a water treatment plant. They had big shrinkage holes in the thick flange, so we redesigned the gating to direct metal straight into the flange, added a larger hot riser, switched to olivine sand, and preheated the mold. We went from 15% rejects to zero. It’s not rocket science, it’s just applying the right tweaks.

Now, let’s be real — no method is perfect. If you’re dealing with a part that’s super complex, or has really tight tolerances, you might even use computer modeling these days. We use a basic solidification modeling tool (like SolidCast, but you don’t need the fancy expensive one) to simulate how metal will cool in the mold before we pour. It lets us spot shrinkage hot spots before we even make the mold, so we can adjust risers or gating instead of wasting material on test pours. For small runs, modeling might feel overkill, but for medium to large batches, it saves so much time. I’ve spent way too many years doing test pours just to get riser size right — modeling cuts that down to one or two tests max.

At the end of the day, reducing shrinkage is all about consistency. You can’t pour metal at 1,900°F one time and 1,800°F the next and expect the same results. That’s why we have a strict process at our shop: log every pour temp, every mold preheat temp, every riser size, and track reject rates per batch. If a batch has a shrinkage issue, we look back at that log to see what changed. It’s simple, but it works.

If you’re dealing with shrinkage headaches, overpaying for reworked parts, or missing deadlines because of bad castings, we can help. As a brass casting supplier that’s worked with dozens of industries (automotive, agriculture, plumbing, decor, you name it), we’ve tweaked these processes to fit all kinds of parts, from tiny 1/4-inch pins to 100-pound industrial components. We can review your current process, adjust gating or riser design, switch to better mold materials, or even test a custom alloy mix to cut shrinkage way down. Hit us up to chat about your next order, we’re all about solving problems, not just selling castings.

Glass Deck Railing References

  1. Campbell, J. (2015). Complete Casting Handbook: Metal Casting Processes, Metallurgy, Design and Testing. Butterworth-Heinemann.
  2. Nafisi, S., & Ghomashchi, R. (2018). Shrinkage Porosity in Metal Castings: Formation, Detection, and Mitigation. Journal of Materials Processing Technology.
  3. American Foundry Society. (2020). Sand Casting Practices for Non-Ferrous Alloys. AFS Technical Report.
  4. Taylor, H. F., Flemings, M. C., & Wulff, J. (1959). Foundry Engineering. John Wiley & Sons.

Dongguan Life-Style Casting Co., Ltd.
Dongguan Life-Style Casting Co., Ltd. is known as one of the most professional brass casting manufacturers and suppliers. Please be free to wholesale bulk discount brass casting made in China here get pricelist from our factory.
Address: Zhonghuiliyang Shidai, Dongcheng, Dongguan, Guangdong, China
E-mail: info@life-stylecasting.com
WebSite: https://www.lifestylecasted.com/